specification dr-4505 DR-4512 dr-4515 dr-4524 model dc voltage rated current current range rated power output voltage adj. range line regulation load regulation setup, rise time hold up time (typ.) voltage range frequency range efficiency (typ.) ac current (typ.) input inrush current (typ.) leakage current over temperature safety standards harmonic current ems immunity working humidity working temp. storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage 5v 12v 15v 24v 5a 3.5a 2.8a 2a 0 ~ 5a 0 ~3. 5a 0 ~ 2.8a 0 ~ 2a 25w 42w 42w 48w 100mvp-p 200mvp-p 240mvp-p 13.5 ~ 16.5v 480mvp-p 21.6 ~ 26.4v 2.0% 1.0% 1.0% 1.0% 10.8 ~ 13.2v 4.75 ~ 5.5v 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 800ms, 60ms/230vac at full load 100ms/230vac at full load 85 ~ 264vac 120 ~ 370vdc 47 ~ 63hz 72% 77% 77% 80% 1.5a/115vac 0.75a/230vac cold start 28a/115vac 56a/230vac <1ma / 240vac 105 ~ 150% rated output power protection type : constant current limiting, recovers automatica lly after fault condition is removed 5.75 ~ 6.75v protection type : shut off o/p voltage, clamping by zener diode 13.8 ~ 16.2v 17.25 ~ 20.25v 27.6 ~ 32.4v tj 135 typically (u1) detect on heat sink of power transistor protection type : shut down o/p voltage, re-power on to recover -10 ~ +50 (refer to output load derating curve) 20 ~ 90% rh non-condensing -20 ~ +85 , 10 ~ 95% rh 0.03%/ (0 ~ 50 10 ~ 500hz, 2g 10min./1cycle, period for 60min. each along x, y, z axes; moun ting: compliance to iec60068-2-6 364.6k hrs min. mil-hdbk-217f (25 ) 93*78*67mm (l*w*h) 0.31kg; 48pcs/16.1kg/1.3cuft 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still me ets emc directives. file name:dr-45-spec 2008-04-07 ul508, tuv en60950-1 approved compliance to en55011,en55022 (cispr22) class b compliance to en61000-3-2,-3 compliance to en61000-4-2,3,4,5,6,8,11, env50204, en55024, en61000-6-2 (en50082-2), heavy industry level, criteria a 45w single output industrial din rail power supply d r - 4 5 s e r i e s universal ac input/full rangeprotections: short circuit / overload / over voltage / over temperature cooling by free air convection can be installed on din rail ts-35/7.5 or 15 ul 508(industrial control equipment)approved led indicator for power on 100% full load burn-in test fix switching frequency at 100khz 3 years warranty features : ripple & noise (max.) note.2 voltage tolerance note.3 environment protection safety & emc (note 4) withstand voltage isolation resistance i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms/500vdc emi conduction & radiation
46.5 77 93 install din rail ts35/7.5 or ts35/15 8.5 78 7.5 67 29 46.5 terminal pin no. assignment pin no. pin no. 2 1 6,7 3 4,5 89 assignment assignment fg dc output -v ac/l ac/n dc output+v led +v adj. 1 74 2 3 5 6 8 9 pwm circuit detection emi filter rectifiers & filter power switch- filter & rectifiers +v -v ing control i/p fg -10 0 10 20 30 40 50 60 (vertical) 20 40 60 80 100 ta=25 200 80 8 70 12 16 20 24 140 100 120 180 160 28 32 260 240 220 50 100 150 200 250 300 350 block diagram static characteristics (24v) ambient temperature ( ) input voltage (v) 60hz load (%) output voltage (v) output ripple (mvp-p) fosc : 100khz mechanical specification file name:dr-45-spec 2008-04-07 35 derating curve case no. 918a unit:mm 45w single output industrial din rail power supply d r - 4 5 s e r i e s
|
